KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
VM-22H
2x1:2 HDMI Switcher/DA
P/N: 2900-000663 Rev 3
Contents
Figures
VM-22H – Contents
i
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Products.
Congratulations on purchasing your Kramer VM-22H 2x1:2 HDMI Switcher/DA,
which is ideal for the following typical applications:
ï‚·
ï‚·
Home theater, presentation and multimedia applications
Rental and staging
VM-22H - Introduction
1
2
Getting Started
We recommend that you:
ï‚·
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
ï‚·
Review the contents of this user manual
to check for up-to-date user manuals, application programs, and to check if
firmware upgrades are available (where appropriate).
i
2.1
Achieving the Best Performance
To achieve the best performance:
ï‚·
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
ï‚·
ï‚·
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
ï‚·
Position your Kramer VM-22H away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
!
2
VM-22H - Getting Started
2.2
2.3
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
!
Warning: Use only the Kramer Electronics input power wall
adapter that is provided with the unit
Warning: Disconnect the power and unplug the unit from the wall
before installing
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
VM-22H - Getting Started
3
3
Overview
The VM−22H is a distribution amplifier for HDMI signals. The unit reclocks and
equalizes one of two selectable input signals and distributes it to two identical
outputs.
In particular, the VM-22H features:
ï‚·
A maximum data rate of 6.75Gbps (2.25Gbps bandwidth per graphic
channel
ï‚·
I-EDIDProâ„¢ Kramer Intelligent EDID Processingâ„¢, an intelligent EDID
handling and processing algorithm that ensures Plug and Play operation for
HDMI systems
ï‚·
Kramer Equalization & re-Klockingâ„¢ Technology that rebuilds the digital
signal integrity to travel longer distances
ï‚·
ï‚·
ï‚·
ï‚·
3D pass-through
HDMI support for Deep Color, x.v.Colorâ„¢, Lip Sync, CEC
HDCP compliance
Selected input and active output LED indicators
The VM-22H is 5V DC fed and is housed in a DigiTOOLS® enclosure.
Defining the VM-22H 2x1:2 HDMI Switcher/DA
This section defines the VM-22H.
3.1
4
VM-22H - Overview
Figure 1: VM-22H 2x1:2 HDMI Switcher/DA
#
Feature
Function
1
5V DC
+5V DC connector for powering the unit
Connects to the HDMI acceptor 2
Connects to the HDMI acceptor 1
Connects to the HDMI source 2
Connects to the HDMI source 1
2
3
4
5
6
HDMI OUT2 Connector
HDMI OUT1 Connector
HDMI IN 2 Connector
HDMI IN 1 Connector
REMOTE IR
The yellow LED illuminates when receiving signals from the
Infrared remote control transmitter
7
EDID SETUP Button
Press briefly to determine the type of EDID stored in the non-
volatile memory. Press and hold to select the desired EDID
8
9
IN SELECT Button
Press to select the input. The relevant IN LED illuminates
Illuminates when input 1 is selected
IN 1 LED
10 IN 2 LED
Illuminates when input 2 is selected
11 OUT 1 LED
Illuminates when output 1 is connected and active (also
12 OUT 2 LED
Illuminates when output 2 is connected and active (also
13 ON LED
Illuminates when receiving power
VM-22H - Overview
5
4
Connecting the VM-22H
Always switch off the power to each device before connecting it to your
VM-22H. After connecting your VM-22H, connect its power and then
i
switch on the power to each device.
To connect the VM-22H as illustrated in the example in Figure 2:
1. Connect the HDMI source (for example, a DVD player) to the HDMI
IN 1 connector.
2. Connect the HDMI source (for example, a DVD player) to the HDMI
IN 2 connector.
3. Connect the HDMI OUT connectors to up to two HDMI acceptors, as follows:
.
.
HDMI OUT 1 connector to an LCD TV
HDMI OUT 2 connector to a plasma display
4. Connect the 5V DC power adapter to the power socket and connect the
adapter to the mains electricity.
5. Press the EDID SETUP button to acquire or change the EDID information
Figure 2: Connecting the VM-22H 2x1:2 HDMI Switcher/DA
6
VM-22H - Connecting the VM-22H
5
Acquiring the EDID
This is usually done only once, when the machine is being set up in an installation.
Once acquired, the EDID is saved in non-volatile memory and further acquisition is
not necessary.
Initially, the VM-22H operates with the factory default EDID. This lets you connect
the power before connecting one of the acceptors or sources.
You can acquire the EDID from:
ï‚·
ï‚·
ï‚·
One output (the relevant output illuminates)
The default EDID (both output LEDs blink)
Two connected outputs, the auto-mix mode (both output LEDs illuminate)
The EDID acquired is a weighted average of all the connected outputs. For example, if
several displays with different resolutions are connected to the outputs, the acquired
EDID supports all the resolutions, as well as other parameters included in the EDID.
When pressing the EDID SETUP button briefly, the OUT LEDs indicate which type
of EDID was last acquired. If the:
ï‚·
ï‚·
ï‚·
ï‚·
OUT 1 LED illuminates, the OUT 1 EDID is stored in the non-volatile
memory
OUT 2 LED illuminates, the OUT 2 EDID is stored in the non-volatile
memory
OUT 1 and OUT 2 LEDs blink, the Default EDID is stored in the non-volatile
memory
OUT 1 and OUT 2 LEDs illuminate, the Auto-Mix EDID is stored in the non-
volatile memory
To acquire the EDID, do the following:
1. Connect the power.
2. Connect the output or outputs from which you want to acquire the EDID.
VM-22H - Acquiring the EDID
7
3. Press and hold the EDID SETUP button to select the desired EDID.
The OUT LEDs illuminate in the following cycle: OUT 1, OUT 2, both flash
(default) and both illuminate (auto-mix).
4. Release the button when reaching the desired set up.
The EDID is now acquired.
If you set the machine to acquire the EDID from an output that is not connected, the
default EDID is acquired.
8
VM-22H - Acquiring the EDID
6
Technical Specifications
INPUTS:
2 HDMI connectors
OUTPUTS:
2 HDMI connectors
MAX. DATA RATE:
6.75Gbps (2.25Gbps per graphic channel)
Supports HDMI and HDCP
COMPLIANCE WITH HDMI
STANDARD:
CONTROLS:
EDID SETUP button, input select button
IN 1, IN 2, OUT 1, OUT 2, and ON LEDs
5V DC, 910mA
INDICATOR LEDs:
POWER CONSUMPTION:
OPERATING TEMPERATURE:
STORAGE TEMPERATURE:
HUMIDITY:
0° to +40°C (32° to 104°F)
-40° to +70°C (-40° to 158°F)
10% to 90%, RHL non-condensing
12cm x 7.15cm x 2.44cm (4.7" x 2.8" 0.96") W, D, H
0.3kg (0.67lbs) approx.
DIMENSIONS:
WEIGHT:
INCLUDED ACCESSORIES:
Power supply, bracket installation kit, infrared remote
control transmitter
OPTIONS:
HDMI/HDMI male-to-male cables
VM-22H - Technical Specifications
9
10
VM-22H - Technical Specifications
For the latest information on our products and a list of Kramer distributors,
visit our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
!
P/N:
Rev:
2900- 000663
3
|
PYLE Audio Mobile Video System PLD41MUT User Manual
Philips CED750 User Manual
PhatNoise KDC W6531 User Manual
Pelco Camera Lens 13FFD V5PAK User Manual
Panasonic Palmcorder PV GS70 User Manual
Panasonic HDC DX1P User Manual
Oster BLSTET B User Manual
O'Brien DELTA DOUBLE 2091505 User Manual
Lochinvar KNIGHT 210 User Manual
LG Electronics W1642S User Manual